Custom Reusable Snack & Sandwich Bags: What to Specify Before You Order

Views: 0     Author: Site Editor     Publish Time: 2026-11-19      Origin: Site

Six of the seven snack and sandwich bags on our line are the same 17 × 17 cm square. That is not a design habit. A 17 cm square is about the smallest panel that takes a sandwich cut into quarters, a handful of grapes and a small tub without the contents sliding into one corner — and because the size is fixed, it tells you where customisation actually happens: in the liner, in the closure, and in the print.

That changes the brief. A reusable snack bag is a food-contact product before it is a printed giveaway, and a purchase order that treats it as a miniature tote leaves the three decisions that set both the unit price and the compliance paperwork still open. This page covers those three, the four documents a buyer should ask for, and the two care claims that most often fail after the first wash.

A snack bag is a food-contact item, not a small tote

On a shopping bag, the questions are structural: does the handle hold, does the seam hold, does the print survive a hundred trips. On a snack bag they are chemical as well as structural, because the inside surface is in direct and repeated contact with food, usually with something greasy, sometimes warm, and the bag is then washed and used again.

Three consequences follow, and all three land on the buyer rather than the factory:

  • The inner surface has to be named, not described. "Food grade" is a marketing phrase. A liner material with a grade and a test report behind it is a specification.

  • Grease is the hard test, not water. Almost any coated fabric resists a splash. A bag that holds a buttered roll for two hours without a dark patch on the outside is a different product.

  • Washability is a claim with a number behind it. "Machine washable" means a stated temperature and a stated number of cycles the closure and the print are expected to survive.

This is why the same 17 cm square can be quoted at three very different prices without anyone being dishonest. The shape is identical; the liner is not.

Three constructions, and what each one is actually good at

Our own line runs three, and they are not interchangeable upgrades of one another — each is the right answer to a different brief.

Construction

What it is

Strong at

Where it runs out

Non-woven with coating

PP non-woven with a coated inner face

Lowest unit cost; holds a printed design well; stiff enough to stand open on a counter

Wipe-clean only, not machine washable; the coating can crack along a fold line after repeated creasing

Food-safe cotton, sewn

Sewn cotton with a fold-over flap; hook-and-loop closure

Breathable, genuinely machine washable, the natural-fibre story holds up in retail copy; the flap takes a name in pen

No inherent moisture barrier — grease and a wet apple pass through unless it is lined; heavier per piece than a film bag

Polyester outer with TPU inner

Woven polyester face bonded to a thermoplastic polyurethane liner

Wipe-clean and machine washable, water- and grease-resistant, BPA-free formulations available, weldable seams

Highest material cost of the three; the TPU face shows crease marks; heat tolerance is finite, so no microwave or dishwasher claim

The practical reading: if the bag is a promotional item handed out once and used for snacks at a desk, the coated non-woven does the job at the lowest cost. If the selling proposition is natural materials and the buyer will actually launder it, cotton is the honest answer, and it needs a lining decision. If the brief includes "leak-resistant" or "washable" as a promise on the packaging, only the polyester-and-TPU build supports it.

The liner is what you are really buying

Four liner families turn up in this product category, and the differences that matter to a buyer are not the ones the names suggest:

  • TPU — flexible, weldable, grease-resistant, tolerates machine washing, and available in food-contact grades. It is the liner that supports the widest set of claims, and it is priced accordingly.

  • PEVA — chlorine-free, common in food wraps, softer and cheaper than TPU. It is a reasonable choice for a wipe-clean bag; its heat tolerance is lower, so a hot sandwich is a question to ask rather than assume.

  • LDPE film — the cheapest sealable option. It creases, it punctures at the corner seams, and after twenty wash cycles it looks like what it is. Fine for a single-season promotional run; wrong for a retail product with a repeat purchase.

  • Coated fabric — a coating applied to non-woven or canvas. Cheapest of all, wipe-clean only, and the failure mode is a crack that opens at the fold rather than a leak at the seam.

Ask for the liner by name and grade, and ask whether the same liner is used on the inside face of the flap. A flap lined with a different material from the body is a common cost saving and a common source of a leak complaint, because the flap is where the bag folds and where the contents press hardest.

Closure: hook-and-loop, press-seal, or zip

Every bag on our line closes with hook-and-loop, which is the right default for a small fabric pouch. It is not the only option, and the choice is a wash-durability decision as much as a sealing one.

Closure

How it behaves

After repeated washing

Best for

Hook-and-loop strip

Fast, forgiving of a mis-fold, works on fabric without stiffening it

The hook face collects lint and thread; grip weakens gradually rather than failing outright; the hook side can abrade the fabric it presses against

Children's bags, cotton construction, anything a five-year-old opens unaided

Press-seal (zipper-lock style) strip

Needs a flat, stiff-ish face to close evenly; sewn or welded in as a strip

Holds well while the weld is intact; the weld is the failure point, not the seal

Film-lined bags where a liquid-resistant close is the promise

Nylon coil zip with slider

Best seal and the most secure close; adds hardware and stiffness

Durable, but the slider is a small part

Adult lunch and travel use; not a children's product without a small-parts review

The point that gets missed in a brief: a hook-and-loop strip is also a print constraint. It has to sit clear of the printed panel, or the artwork needs a keep-out zone marked on the dieline. Suppliers who are asked to "print the full front" and given no keep-out will solve it by shrinking the design.

Why the 17 × 17 cm size repeats across the range

Because the size is doing a job, not expressing a style. At 17 cm the bag takes a sandwich quartered, a child's snack portion, or a small tub laid flat; below that the sandwich has to be cut to fit, above it the bag stops being a snack bag and becomes a lunch bag, which is a different product with a different liner requirement.

The commercial consequence is useful. If the size is fixed, the variables your design and your price depend on are the liner, the closure, the print method and the packaging — four decisions, all of them visible in a quote, none of them hidden in a dimension. A buyer who specifies those four can compare three suppliers line by line. A buyer who specifies "a snack bag, about 17 cm" gets three quotes that cannot be compared and picks on price.

A second, smaller point: on a 17 cm square the seam allowance is a larger share of the finished size than on a shopping bag. Reducing the seam to save material is one of the quiet ways a supplier meets a target price, and it is visible only when the bag is turned inside out.

The roll bag is a different product, not a bigger pouch

One item on our line is not a 17 cm pouch: a 54 × 32 cm sandwich roll bag. The size is not a scaled-up version of the square. It is a flat sheet that wraps a roll or a baguette and closes on itself, so the geometry is a rectangle rather than a bag — and the specification questions change with it.

On a roll bag the questions are the fold line and the closure position, not the gusset. The sheet has to be wide enough to wrap the diameter of the roll with an overlap, the closure strip has to land where the wrap ends rather than where the print looks balanced, and the whole thing has to lie flat in a carton so that packing density stays sensible. Ask for the flat dimensions and the intended roll diameter, in figures, before approving artwork — artwork approved on the flat sheet without the wrap position marked is the usual cause of a closure strip printed in the wrong place.

Food-contact compliance: the four documents to ask for

This is the part that separates a promotional order from a retail one, and it is entirely the buyer's homework. Four documents cover most of it. Ask for them by name, and ask that they name the exact construction you are ordering — a certificate for a different liner proves nothing about yours.

Document

What it should say

Why it matters

Declaration of compliance

Names the material, the regulation it is declared against, and the conditions of use (temperature, food type, contact duration)

It is the document a retailer's compliance team will ask you for, and the one a general "food grade" statement cannot substitute for

Migration test report

Overall and specific migration results, from an accredited laboratory, on the finished article

Tests on raw material do not cover the seam, the weld or the print

BPA and phthalate statement

States the limit tested against, not just "free"

"BPA free" without a limit and a test method is a marketing claim

Ink and adhesive declaration

Confirms the print and any lamination adhesive are suitable for food-contact use, or that a functional barrier sits between them and the food

Ink on the outside is not automatically out of scope if the film is thin

Two further points if the bag will be sold as a children's product. First, several markets impose their own children's-product rules — in the United States that includes testing and a tracking label obligation, and a small-parts assessment where the item is intended for children under three. Second, a zip slider, a metal snap or a decorative button turns a fabric pouch into an item with a small part, and that has to be reviewed before the design is frozen rather than after. Both are questions for your testing laboratory against your market; they are not questions a factory can answer on your behalf.

Printing on a 17 cm panel

The printable area on a 17 cm bag is small enough that the print method decides how much of the design survives, and the wash requirement decides which methods are available at all.

  • Screen print — one screen per colour, opaque on both coated non-woven and cotton, and durable through washing when cured correctly. The limit is the colour count, because each screen has to fit a 17 cm panel without the registration drifting.

  • Heat transfer — the only route to a photographic or gradient design at this size. It handles fine detail the other methods cannot, and its durability depends on the film rather than the ink.

  • Digital direct — no setup, so short runs and multi-design orders become viable, at a higher per-piece cost and with a wash-durability that has to be confirmed on the actual liner.

  • Woven label or printed flap — for a brand that wants a permanent mark, a label on the flap or the inside seam survives everything the surface print does not.

Two constraints apply whatever the method. The print should stop clear of the seam allowance and the closure keep-out, which on a panel this small is a real share of the area. And if the ink could contact food through a thin liner, the safe design answer is to keep print off the inner face entirely and use a label for the inside — cheaper than proving the ink is compliant.

What drives the unit price

Six variables move the price on a snack bag. They are listed in roughly the order of their effect, and only the first is a material decision.

Variable

What changes

Where buyers overspend

Liner material

Coated non-woven at one end, polyester with a TPU liner at the other

Specifying a washable liner for a bag that will be handed out once

Closure

Hook-and-loop strip is the cheapest; a coil zip with a slider is the most expensive and adds hardware handling

A zip chosen for a retail look that the design does not need

Print method and colour count

Each screen adds setup; heat transfer adds a film; digital removes setup and adds unit cost

A four-colour design on a 17 cm panel where two colours would read better and cost less

Seam and construction

Turned-and-topstitched versus welded; gusset versus flat

Assuming every supplier builds the same seam at the same price

Retail packaging

Plain poly bag, header card, hang tag, or a printed sleeve

Treating packaging as free and discovering it is a per-unit line item

Order quantity and colour split

Material is bought by the roll; a size or colour split below the roll length carries the waste

Splitting a small order across four colours and paying for the offcut

The one figure worth knowing before the conversation: on our line a development sample takes about seven days from an approved artwork file. Production timing for a snack bag is a different question from a shopping bag — the unit is far smaller and the run is counted in different volumes — so ask for the number against your actual construction and quantity rather than extrapolating from a tote. The lead-time breakdown sets out which stages are the factory's and which are yours.

Care claims you can print, and the ones you cannot

Care instructions are printed on the product and then tested by the customer in a kitchen. They are a promise with a legal edge, so they should be written against the construction rather than copied from a competitor's tag.

  • "Machine washable" — defensible on the cotton build and on polyester with a TPU liner, with a stated temperature. Not defensible on coated non-woven.

  • "Wipe clean" — true of all three, and the honest claim for the coated non-woven.

  • "Waterproof" — a seam is a hole. Say water-resistant, or state the test the claim is based on.

  • "Leak-proof" — only against a defined test, and only for a welded or sealed construction. A sewn seam with a coated fabric will wick at the stitch line.

  • "Microwave safe" or "dishwasher safe" — do not print these on a TPU-lined fabric bag. Both exceed what the material is specified for.

  • "Food safe" — replace it with the specific statement your declaration of compliance supports.

The two claims that fail most often in the field are machine washability on a coated non-woven, and leak resistance on a sewn seam. Both survive a sampling round and fail at the two-hundredth wash or the first yoghurt.

Write these into the RFQ

What to state

Why it removes a re-quote

The construction, by liner name

"Food grade" fits three materials at three prices; a named liner fits one

Finished dimensions, and whether the flap is included

On a 17 cm panel a 1 cm difference in the flap changes the cut

Closure type and position

A closure strip is a keep-out zone for print; deciding it after artwork costs a second round

The wash claim you intend to print

It decides the liner and the ink, and it is the first thing a customer tests

Print method, colour count and Pantone references

Sets the screens and the setup cost before the quote is built

Whether the item is marketed to children

Changes the testing, the labelling and the hardware rules

The destination market and the documents required

Compliance paperwork is a duration in its own right, not a formality at the end

Retail packaging and how it is packed for shipping

Both are per-unit or per-carton cost lines, not overheads

The RFQ template is already formatted in this order, and the price driver breakdown explains which of these choices moves the unit cost rather than only the schedule.

Questions buyers ask before ordering

What size is a standard reusable snack bag?

Seventeen by seventeen centimetres on six of the seven bags on our line, which takes a sandwich quartered, a child's snack portion, or a small tub laid flat. Below that the sandwich has to be cut to fit; above it the product becomes a lunch bag and needs a different liner specification. A sandwich roll bag is a separate shape entirely — a flat wrap rather than a pouch.

What is the difference between the cotton and the TPU-lined version?

The cotton bag is breathable, genuinely machine washable, and supports a natural-fibre story, but without a lining grease and moisture pass through. The polyester bag with a TPU liner resists both, is also machine washable, and supports water- and grease-resistance claims — at a higher material cost. If the packaging will say "leak-resistant" or "washable", only the second build supports it honestly.

Can the bag be printed on both sides?

Yes, and on a 17 cm panel it usually should be, because one side alone leaves the flap and the back blank. What has to be respected is the keep-out: the seam allowance, the closure strip and, on the cotton build, the flap where a name is written. Mark all three on the dieline before artwork starts.

Is a reusable snack bag actually more sustainable than a disposable one?

Only past a break-even number of uses, and the number depends on the liner and the weight. A heavier, lined, retail-packaged bag needs more trips to beat a thin disposable film than a light unlined one does. That is an argument for publishing a care instruction that keeps the bag in use, not for claiming an environmental result the material has not earned.

What paperwork does a retailer ask for?

Typically a declaration of compliance naming the construction and its conditions of use, a migration test report from an accredited laboratory on the finished article, a BPA and phthalate statement with the limits tested against, and confirmation on the ink and any lamination adhesive. Where the item is sold as a children's product, add the testing and labelling that the destination market requires.

Can we start from an existing bag and change only the print?

Yes, and it is the fastest route to a first order — keeping the liner, closure and dimensions fixed and changing only the artwork removes the sampling variables. Send the artwork against the existing dieline, with the closure keep-out marked, and the sample round is about the print alone.

Where this fits on our line

We make custom reusable snack and sandwich bags in the snack bag range alongside the wider reusable shopping bag line — the same constructions described here appear across coated non-woven, cotton and canvas, and certified recycled fibre where the brief calls for it. What we check at each stage is set out on our quality control page, and the sequence from artwork to carton on our customization process page.

Send the liner, the closure, the wash claim you intend to print and the destination market through the contact form, and we will come back with the construction that supports all four — and tell you if one of them has to give.

Set up in 2007, as one of the main manufacturers specialized in making shopping bags with the eco friendly material, Zhejiang Meige Bags Co., Ltd. is located in Cangnan, Zhejiang Province, which is known as "the city of bag industry" in China. 
  #No. 8, Jinxin Middle Road, Qianku Industrial Zone, Cangnan County, Wenzhou City, Zhejiang, China. 
 0086-577-59867999
 0086-577-59867999
Whatsapp : +86 18072166905
WeChat/Phone : 18966277555
Home
Free Design
WeChat
Production Base
© 2020 Zhejiang Meige Bags Co., Ltd. All Rights Reserved.